DryPro is highly rated on many platforms and is truly an innovative amputee product that we are proud to sell. Please note that our price includes free express shipping.
Unlike cast covers, these prosthetic covers are made to last longer rather than a temporary product and are intended for swimming and showering. This is a must have for any leg amputee.
Please take note of sizing and how to measure for a good fit.
Due to hygienic reasons we will not be accepting returns on this product at this time unless it is due to manufacturer defect or an error on our part. This product is made from latex, please be aware for latex allergies and sensitivities.
How to Use - Easy as 1, 2, 3!
1. Slide On
Stretch on the DRYPro over the arm or leg with the cast or bandage to see how it fits. The DRYPro opening should fit tightly to the skin. The top of the DRYPro should be smooth against the skin and the hand or foot should reach to the end of the cover. The vacuum will remove any excess material. Be careful as sharp fiberglass on a cast can rip the DRYPro. Cover sharp objects with a bandage or sock.
2. Pump Out the Air
Attach the long end of the pump on to the outside valve. Continuously press the pump until it becomes flat. Remove the pump and push on the safety cap. After creating the vacuum seal, observe the DRYPro for about five minutes before going in the water. As long as the DRYPro stays vacuumed (tightly wrinkled), it is sealed and completely watertight.
3. Slide Off
When you are done using the DRYPro, simply lift up the cuff to let the air back in. The DRYPro should now be loose. Simply slide it back off. The DRYPro can be rinsed off or cleaned with soap and water. You can put the DRYPro back in the plastic box for the next use.
- Dry Pro Measurements charts and guides
Model #
Arm/Leg Circumference
Length
X-Small Full Arm
FA-12
6 – 6.75 inches
16 inches
Small Full Arm
FA-14
6.75 – 8.75 inches
23 inches
Small Half Arm
HA-13
7.75 – 10 inches
17.5 inches
Large Half Arm
HA-15
10 inches & up
20 inches
Medium Full Arm
FA-16
8.75 – 10 inches
28 inches
Large Full Arm
FA-18
10 inches & up
31.5 inches
X-Small Full Leg
FL-12
7.5 – 11 inches
19 inches
Small Half Leg
HL-13
10 – 13 inches
21 inches
Large Half Leg
HL-15
13 inches & up
23.5 inches
Small Full Leg
FL-14
14 – 16.5 inches
29 inches
Medium Full Leg
FL-16
16.5 – 21 inches
33 inches
Large Full Leg
FL-18
21 inches & up
37 inches
*Keep in mind, to achieve the best fit, consider both half and full sizes.
Measuring Circumference: Measure the circumference of the arm or leg at 2 inches above the cast. If the end of the cast is very close to the elbow/knee, then measure mid-bicep/mid-thigh. Do not measure around the cast! Only measure around the skin of the arm/leg above the cast.
Measuring Length: Measure from the tip of the middle finger or heel of the foot to 2 inches above the top end of the cast. It is okay if the cast protector measurement is longer then the limb measurement. The protector will still work. Extra length will be removed when the vacuum seal is created.
X-Small Prosthetic Leg
PL-11
8 -12 inches
29 inches
Small Prosthetic Leg
PL-13
12 – 16 inches
32 inches
Medium Prosthetic Leg
PL-15
15 – 19 inches
35 inches
Large Prosthetic Leg
PL-17
17 – 21 inches
38 inches
X-Large Prosthetic Leg
PL-19
21 inches & Up
41 inches
Stretch on the DryPro Prosthetic Leg Cover: Pull over the leg to see how it fits. If the DryPro is too tight, you can trim 1/4 inch along the lines towards the top of the opening and try it on again. Be sure not to trim too much, as a tight seal is needed for the vacuum to work. Stretch the DryPro over the prosthetic so the top fits smooth against the skin. Allow some slack as the vacuum will remove the excess material.